: FITTER – FABRICATION /

MECHANICAL

Company: Kanha Metal Works (KMW)

Employment Type: Full-time / Contractual

Work Location: KMW Workshop / Factory

Experience: 2–5 years preferred

Wage Type: Daily wages

1. Job Purpose

KMW is hiring a skilled Fabrication / Mechanical Fitter to perform marking, measuring,

fitting, alignment, assembly, and modification of metal components. The candidate must ensure dimensional accuracy, compliance with approved drawings and specifications,

safe working practices, and timely completion of fabrication jobs in accordance with

KMW quality standards and applicable internal Heartfulness requirements.

2. Key Responsibilities

A.

Fabrication

Fitting and Assembly

- Read and interpret engineering and fabrication drawings, dimensions, tolerances,

and work instructions.

- Mark, measure, prepare, fit, and assemble metal plates, sections, frames,

brackets, supports, channels, angles, pipes, and other fabricated components.

- Ensure correct dimensions, alignment, levels, clearances, hole positions, and component orientation before welding or final assembly.
- Perform mechanical assembly, bolting, fastening, drilling, grinding, deburring,

and minor finishing using appropriate tools.

- Prepare components for tack welding and coordinate with welders to maintain alignment and minimize distortion.
- Carry out dismantling, adjustment, modification, and reassembly as instructed.
- Identify and report mismatched, damaged, distorted, or incorrectly fabricated components and drawing discrepancies.

B. Measurement and Quality Control

- Use measuring tapes, steel rules, squares, spirit levels, vernier calipers, and other suitable measuring instruments.
- Verify dimensions, squareness, parallelism, alignment, fit-up, joint gaps, and other specified tolerances during fitting and assembly.
- Rectify routine fitting defects within authorized limits and escalate major discrepancies to the supervisor.
- Support in-process and final inspections by providing measurements and access to components.
- Minimize dimensional errors,



rework, material wastage, and damage to finished components.

C. Tools, Equipment, and Production Coordination

- Select, operate, and maintain appropriate hand tools, grinders, drills, spanners,

clamps, and approved power tools.

- Inspect tools and equipment before use, store them properly, and report defects or unsafe conditions.
- Confirm the availability and correctness of materials, components, fasteners, and consumables before starting work.
- Coordinate with supervisors, welders, helpers, stores personnel, and other fitters to meet production schedules and ensure smooth movement of components through fabrication, welding, grinding, inspection, and finishing.
- Report material shortages, equipment issues, drawing clarifications, and production delays; maintain required job and material records.

D. Safety and Housekeeping

- Follow KMW safety procedures and wear task-appropriate PPE, including safety footwear, gloves, eye protection, and hearing protection where required.
- Handle heavy components, sharp edges, hot metal, and suspended loads safely using appropriate supports, clamps, and authorized lifting equipment.
- Operate machinery and power tools only when trained and authorized.
- Maintain clean and organized workstations and tool storage areas; keep walkways and emergency access routes clear.
- Follow scrap segregation and waste-disposal procedures and immediately report accidents, near misses, equipment defects, and unsafe conditions.

3.

Qualifications and Experience

- ITI in Fitter, Mechanical Fitter, Fitter-Fabrication, or a related trade is preferred;





candidates with demonstrable practical fitting skills may also be considered.

- Preferably 2–5 years of experience in metal fabrication, mechanical fitting,

structural fabrication, industrial assembly, or a similar workshop environment.

- Ability to interpret basic engineering and fabrication drawings and understand dimensions and tolerances.
- Practical proficiency in measuring, marking, alignment, drilling, grinding, bolting,

and mechanical assembly.

- Ability to understand work instructions and safety procedures in a language understood by the candidate.
- Ability to work independently on assigned jobs while coordinating with the production team.

4.

Required Skills and Personal Attributes

- Strong practical fitting, alignment, and assembly skills.
- Attention to detail and commitment to dimensional accuracy.
- Ability to identify and resolve routine fitting issues.
- Responsible use of tools, equipment, and materials.
- Good teamwork, communication, discipline, punctuality, and accountability.

5. Wage and Employment Terms The final wage will be determined by KMW based on practical assessment, experience,

drawing interpretation, dimensional accuracy, and job complexity.

Payment will be based on recorded attendance and the agreed wage cycle. Working hours, overtime, weekly rest, leave, and applicable statutory advantages will be governed by company policy and applicable Indian labour laws.

6.

Selection

Process

- Screening of qualifications, experience, and relevant fitting work.
- Practical test covering measurement, marking, tool selection, alignment, and assembly.
- Assessment of drawing interpretation and dimensional accuracy.
- Evaluation of workmanship, safety awareness, and ability to follow instructions.
- Final selection by the authorized KMW representative.

7.

Performance

Expectations The selected candidate must achieve accurate fitting and assembly, meet specified dimensional tolerances, minimize rework, use tools safely, and complete assigned jobs within production schedules.

📌 FITTER – FABRICATION / MECHANICAL (Hyderabad)
🏢 Heartfulness
📍 Hyderabad