1. Main Roles and Responsibilities

1. Work Planning and Coordination

- Plan daily pipeline activities according to the project schedule.
- Review approved drawings, method statements, and work procedures.
- Allocate work to technicians, welders, fitters, helpers, and operators.
- Coordinate with engineers, safety officers, QA/QC inspectors, and subcontractors.
- Ensure manpower, tools, equipment, and materials are available.

2. Pipeline Installation and Construction

- Supervise pipeline route marking, trench excavation, and pipe laying.
- Check pipe alignment, levels, slopes, and installation clearances as applicable.
- Monitor pipe handling, lifting, lowering, jointing, and backfilling activities.
- Ensure valves, fittings, flanges, supports, and other components are installed correctly.
- Verify that work follows approved drawings and project specifications.

3. Welding and Jointing Supervision

- Ensure welding is performed by qualified welders using approved welding procedures (WPS).
- Verify pipe preparation, beveling, fit-up, root gap, and alignment.
- Check welding consumables and required welding parameters.
- Coordinate visual inspection and non-destructive testing (NDT).
- Ensure defective welds are repaired and re-inspected as required.

4. Health, Safety, and Environment (HSE)

- Conduct toolbox talks and daily safety briefings.
- Ensure work permits are approved and valid before starting work.
- Verify that job hazard analysis (JHA/JSA) and risk assessments are in place.
- Ensure workers use appropriate personal protective equipment (PPE).
- Check excavation safety, lifting operations, hot-work controls,



and confined-space precautions where applicable.
- Ensure gas testing, fire watch, and emergency arrangements are in place when required.
- Stop work immediately if an unsafe condition or potential gas leak is identified.

5. Quality Control

- Ensure materials match approved specifications and material certificates.
- Verify pipe identification, material traceability, and inspection records.
- Coordinate inspections with the QA/QC team.
- Check that weld maps, inspection reports, and test records are maintained.
- Ensure non-conformities are corrected before the work proceeds to the next stage.

6. Pressure Testing and Commissioning

- Coordinate hydrostatic or pneumatic testing according to the approved test procedure.
- Verify that test equipment and pressure gauges have valid calibration.
- Ensure test boundaries, isolation points, exclusion zones, and safety precautions are established.
- Monitor pressure, test duration, and leakage checks as specified in the approved procedure.
- Coordinate approved flushing, cleaning, drying, purging, and gas-in procedures where applicable.
- Ensure commissioning is performed only by authorized personnel under approved procedures.

Important: Pneumatic testing and gas introduction can present serious hazards.



Never exceed approved test pressures or carry out unauthorized pressurization or purging.

7. Manpower and Equipment Management

- Monitor attendance, productivity, and workforce performance.
- Ensure tools and equipment are suitable and inspected before use.
- Coordinate cranes, excavators, welding machines, and other required equipment.
- Prevent equipment misuse and report defective tools immediately.
- Monitor daily progress and minimize delays.

8. Documentation and Reporting

- Prepare daily progress reports.
- Record manpower, equipment usage, completed quantities, and delays.
- Maintain inspection requests, work permits, test reports, and material records.
- Report incidents, near misses, defects, and site constraints.
- Communicate progress and problems to the project engineer or construction manager.

9. Environmental Protection

- Prevent soil, water, and air pollution during construction.
- Ensure proper disposal of welding waste, scrap, and other materials.
- Control dust, noise, and accidental spills.
- Follow project environmental procedures and applicable regulations.

10. Final Inspection and Handover

- Verify completion of pipeline installation against approved drawings.
- Ensure punch-list items and defects are closed.
- Coordinate final inspections and required testing.
- Confirm that as-built drawings and quality records are submitted.
- Support safe handover to the client or operations team.

Pay: ₹10,000.00 - ₹25,000.00 per month

Benefits:

- Adaptable schedule
- Leave encashment

Work Location: In person

📌 Site Supervisor (Gas Pipeline Work) (Sreekariyam)
🏢 Ithiel Constructions
📍 Sreekariyam