1. Job Objective – Quality Engineer

To ensure that boiler components, pressure parts, structural steel, piping, welding, fabrication, and erection activities comply with approved drawings, applicable codes, project specifications, inspection and test plans (ITPs), and quality standards.

2. Key ResponsibilitiesA. Incoming Material Inspection

- Inspect incoming raw materials, plates, pipes, tubes, fittings, flanges, and pressure-part components.
- Verify material test certificates (MTCs), material grades, heat numbers, dimensions, and traceability.
- Check materials against approved drawings, purchase specifications, and applicable codes.
- Maintain material inspection reports and traceability records.

B. Welding Quality Control

- Verify approved Welding Procedure Specifications (WPS), Procedure Qualification Records (PQR), and welder qualifications.
- Inspect weld joint preparation, fit-up, root gap, alignment, and preheating requirements.
- Monitor welding activities for pressure parts, headers, steam drums, piping, and structural components, as applicable.
- Verify compliance with approved welding procedures and project specifications.
- Coordinate visual inspection and Non-Destructive Testing (NDT), including RT, UT, MT, and PT, as applicable.
- Monitor weld repairs and ensure re-inspection and documentation.

C. Boiler Erection Quality Inspection

- Inspect boiler pressure parts, including water wall panels, economizer, superheater, reheater, headers, and steam drum, as applicable.
- Inspect structural steel erection, equipment alignment, dimensional tolerances, and support installation.
- Verify installation against approved general arrangement (GA) and erection drawings.
- Inspect site welding, piping installation, supports, and equipment fit-up.
- Raise inspection requests and coordinate inspections with clients, third-party inspectors, and authorized inspection agencies.

D. Quality Documentation

- Prepare and maintain Inspection and Test Plans (ITPs), inspection checklists, and inspection reports.
- Maintain weld maps, weld logs, welder qualification records, and NDT reports.
- Prepare material traceability records, inspection release notes, and quality dossiers.
- Maintain calibration records for measuring and testing instruments.
- Prepare and follow up on Non-Conformance Reports (NCRs), corrective actions, and preventive actions.
- Compile quality documentation for final handover.

E. Testing and Final Inspection





- Coordinate hydrostatic testing of boiler pressure parts and piping systems.
- Verify test readiness, approved test procedures, calibrated instruments, and required inspection clearances.
- Review NDT reports and resolve inspection observations.
- Coordinate final inspections, punch-point closure, and quality clearance before handover.
- Support commissioning teams in resolving quality-related issues.

F. Codes, Standards and Safety

- Ensure compliance with applicable Indian Boiler Regulations (IBR), ASME codes, approved project specifications, and relevant standards.
- Follow the approved Quality Assurance Plan (QAP), ITP, and site quality procedures.
- Ensure inspection activities comply with site safety rules and permit-to-work requirements.
- Coordinate with production, fabrication, erection, engineering, planning, and client quality teams.

1. Job Objective – Erection Engineer:

To supervise and execute the erection, installation, alignment, and commissioning preparation of boiler systems and associated equipment at project sites, ensuring compliance with approved drawings, project schedules, quality standards, and safety requirements.

2. Key responsibilities

A. Boiler erection and installation

- Supervise erection of boiler pressure parts, including water wall panels, economizer, superheater, reheater, headers, and steam drum, as applicable to the project.
- Coordinate installation of boiler structural steel, platforms, staircases, ducting, casing, and supporting structures.
- Supervise erection of coal-fired, biomass-fired, oil/gas-fired, or waste-heat recovery boiler equipment, depending on project scope.
- Ensure correct positioning, alignment, leveling, fit-up, and dimensional accuracy of equipment.
- Coordinate lifting, rigging, crane operations, and heavy equipment handling with the rigging team.

B. Drawing and technical coordination

- Read and interpret GA drawings, fabrication drawings, erection drawings, P&IDs;, and equipment layouts.
- Verify material identification, equipment tags, and component traceability.




- Coordinate with design, planning, QA/QC, welding, and client inspection teams to resolve site issues.
- Prepare and communicate technical queries and site modification requirements for approval.

C. Welding and quality control

- Coordinate pressure-part fit-up, welding, and inspection activities with qualified welding personnel.
- Ensure compliance with approved WPS/PQR, welder qualifications, applicable codes, and project specifications.
- Coordinate NDT, hydrostatic testing, dimensional inspections, and punch-point clearance.
- Maintain erection checklists, inspection requests, test records, and as-built documentation.

D. Site planning and execution

- Execute daily erection activities according to the project schedule and milestone targets.
- Allocate manpower, tools, tackles, and equipment in coordination with site management.
- Monitor productivity, material availability, and subcontractor performance.
- Prepare daily progress reports, weekly reports, and look-ahead plans.
- Coordinate with civil, mechanical, electrical, instrumentation, refractory, and insulation teams.

E. Safety and compliance

- Ensure compliance with site HSE procedures, permit-to-work systems, and approved method statements.
- Enforce work-at-height, confined-space, lifting, and hot-work safety requirements.
- Conduct toolbox talks and identify site hazards before starting work.
- Stop unsafe activities and ensure corrective actions are implemented.

F. Pre-commissioning and handover

- Support boiler flushing, hydrostatic testing, steam blowing, and other applicable pre-commissioning activities.
- Assist in resolving erection-related defects and commissioning punch points.
- Prepare completion dossiers, test certificates, and handover documents.
- Coordinate with commissioning engineers during start-up readiness and performance testing.

Pay: ₹25,000.00 - ₹70,000.00 per month

Perks:

- Food provided
- Life insurance
- Provident Fund

Application Question(s):

- Its a Onsite Job based on the Project Sites, Particularly in West Bengal, Orissa and Chhattisgarh. Are Your Willing to Work these Regionals...
- Do You have an Experience in Boiler Industry?
- Do You have an Experience in Quality , Weld Inspection and Erection and Commissioning Experience?

Language:

- Hindi (Required)

Willingness to travel:

- 100% (Required)

Work Location: In person

📌 Quality Engineer & Erection Engineer (Tiruchirappalli)
🏢 Dynepro Private
📍 Tiruchirappalli