: FITTER – FABRICATION /MECHANICALCompany: Kanha Metal Works (KMW)Employment Type: Full-time / ContractualWork Location: KMW Workshop / FactoryExperience: 2–5 years preferredWage Type: Daily wages1. Job PurposeKMW is hiring a skilled Fabrication / Mechanical Fitter to perform marking, measuring,fitting, alignment, assembly, and modification of metal components. The candidate mustensure dimensional accuracy, compliance with approved drawings and specifications,secure working practices, and timely completion of fabrication jobs in accordance withKMW quality standards and applicable internal Heartfulness requirements.2.

Key ResponsibilitiesA.

Fabrication

Fitting and Assembly1. Read and interpret engineering and fabrication drawings, dimensions, tolerances,and work instructions.2. Mark, measure, prepare, fit, and assemble metal plates, sections, frames,brackets, supports, channels, angles, pipes, and other fabricated components.3.

Ensure correct dimensions, alignment, levels, clearances, hole positions, andcomponent orientation before welding or final assembly.4. Perform mechanical assembly, bolting, fastening, drilling, grinding, deburring,and minor finishing using appropriate tools.5. Prepare components for tack welding and coordinate with welders to maintainalignment and minimize distortion.6.

Carry out dismantling, adjustment, modification, and reassembly as instructed.7. Identify and report mismatched, damaged, distorted, or incorrectly fabricatedcomponents and drawing discrepancies.B. Measurement and Quality Control1.

Use measuring tapes, steel rules, squares, spirit levels, vernier calipers, andother suitable measuring instruments.2. Verify dimensions, squareness, parallelism, alignment, fit-up, joint gaps, andother specified tolerances during fitting and assembly.3. Rectify routine fitting defects within authorized limits and escalate majordiscrepancies to the supervisor.4.

Support in-process and final inspections by providing measurements and accessto components.5. Minimize dimensional errors, rework,



material wastage, and damage to finishedcomponents.C. Tools, Equipment, and Production Coordination1.

Select, operate, and maintain appropriate hand tools, grinders, drills, spanners,clamps, and approved power tools.2. Inspect tools and equipment before use, store them properly, and report defectsor unsafe conditions.3. Confirm the availability and correctness of materials, components, fasteners, andconsumables before starting work.4.

Coordinate with supervisors, welders, helpers, stores personnel, and other fittersto meet production schedules and ensure smooth movement of componentsthrough fabrication, welding, grinding, inspection, and finishing.5. Report material shortages, equipment issues, drawing clarifications, andproduction delays; maintain required job and material records.D. Safety and Housekeeping1.

Follow KMW safety procedures and wear task-appropriate PPE, including safetyfootwear, gloves, eye protection, and hearing protection where required.2. Handle heavy components, sharp edges, hot metal, and suspended loads safelyusing appropriate supports, clamps, and authorized lifting equipment.3. Operate machinery and power tools only when trained and authorized.4.

Maintain clean and organized workstations and tool storage areas; keepwalkways and emergency access routes clear.5. Follow scrap segregation and waste-disposal procedures and immediately reportaccidents, near misses, equipment defects, and unsafe conditions.3.

Qualifications and Experience1. ITI in Fitter, Mechanical Fitter, Fitter-Fabrication,



or a related trade is preferred;candidates with demonstrable practical fitting skills may also be considered.2. Preferably 2–5 years of experience in metal fabrication, mechanical fitting,structural fabrication, industrial assembly, or a similar workshop environment.3.

Ability to interpret basic engineering and fabrication drawings and understanddimensions and tolerances.4. Practical proficiency in measuring, marking, alignment, drilling, grinding, bolting,and mechanical assembly.5. Ability to understand work instructions and safety procedures in a languageunderstood by the candidate.6.

Ability to work independently on assigned jobs while coordinating with theproduction team.4.

Required Skills and Personal Attributes1. Strong practical fitting, alignment, and assembly skills.2. Attention to detail and commitment to dimensional accuracy.3. Ability to identify and resolve routine fitting issues.4.

Responsible use of tools, equipment, and materials.5. Good teamwork, communication, discipline, punctuality, and accountability.5. Wage and Employment TermsThe final wage will be determined by KMW based on practical assessment, experience,drawing interpretation, dimensional accuracy, and job complexity.Payment will be based on recorded attendance and the agreed wage cycle.

Workinghours, overtime, weekly rest, leave, and applicable statutory benefits will be governedby company policy and applicable Indian labour laws.6.

Selection

Process1. Screening of qualifications, experience, and relevant fitting work.2. Practical test covering measurement, marking, tool selection, alignment, andassembly.3. Assessment of drawing interpretation and dimensional accuracy.4. Evaluation of workmanship, safety awareness, and ability to follow instructions.5. Final selection by the authorized KMW representative.7.

Performance

ExpectationsThe selected candidate must achieve accurate fitting and assembly, meet specifieddimensional tolerances, minimize rework, use tools safely, and complete assigned jobswithin production schedules.

📌 Fitter – Fabrication / Mechanical (Hyderabad)
🏢 Heartfulness
📍 Hyderabad