Chief Engineer (Pune)

Chief Engineer (Pune)

19 Nov
|
Antal International
|
Pune

19 Nov

Antal International

Pune

Non-Negotiable Ownership

• System Requirements & Product Architecture — Own and approve the translation of customer, benchmark and programme requirements into system-level actuator requirements, architecture and interfaces.

• Design Authority — Act as final technical authority for architecture freeze, design release, major engineering changes, prototype acceptance and technical release decisions.

• Engineering Standards & Design Rules — Establish calculation practices, design reviews, drawing/release discipline, PLM/configuration control and engineering documentation standards.

• Technical Risk & Gate Evidence — Own the technical risk register and ensure every engineering claim at a programme gate is supported by traceable calculations, measurements or test evidence. • External Specialist Governance — Direct and technically accept external specialist work while ensuring methods, models, drawings and know-how are transferred into -owned capability.

• Verification, Validation & DV Strategy — Approve the overall verification and DV plan, with every requirement linked to a verification method, acceptance criterion and evidence record.

• Technical Organisation & Talent Quality — Lead technical assessment of architects, leads and senior engineering hires and develop delegated technical authority beneath the CTO.

• Technology Roadmap & Technical Make/Buy — Own the technical basis for what builds internally, sources, leverages from Group capability or accelerates through external specialists.

Design & Decision Authority

CTO-only technical authority

• System requirements baseline and product/system architecture. CONFIDENTIAL | CTO / Chief Engineer

• Interface-control architecture covering mechanical, thermal, electrical, encoder/sensing and communications boundaries.

• Engineering design rules, standards, architecture/design freeze and technical release policy.

• Engineering-change / ECN governance and prototype technical acceptance.

• DV approval and sign-off with Quality; customer-facing firmware technical release.

• Technical risk register, engineering tool/method selection and external-expert technical direction/acceptance. • Technical interview-panel leadership for critical engineering hires.

Joint CEO + CTO decisions





• M18 wedge-product selection and anchor-customer programme commitment.

• M18 controlled first-order gate recommendation.

• Strategic maturity route: partner / license / JV / acquisition.

• Architect and functional-lead appointments.

• Material external-expert engagements and expert spend.

• Final customer product release.

Delegation principle: The CTO may delegate domain authority to the Gear / Transmission Architect, Motor & Magnetics Architect, Embedded / Controls Lead and other approved technical leads. Authority is delegated; overall technical accountability remains with the CTO.

Technical Responsibilities

System & Product Architecture

• Translate target-market and customer needs into requirements covering torque, speed, ratio, stiffness, backlash/lost motion, efficiency, thermal limits, envelope, mass, duty cycle, life, environmental conditions, electrical interface, sensing, communications and controllability.

• Lead cross-domain co-design across strain-wave / harmonic drives, QDD integrated actuators, planetary actuators, frameless PMSM motors, bearings and interfaces, servo-drive electronics, embedded control, sensing/encoders, thermal design, firmware and communications.

• Prevent local subsystem optimisation from degrading system performance; require traceable interface decisions and quantified trade-offs.

Engineering Reviews

• Chair formal architecture and design reviews using requirements, calculations and evidence rather than status reporting.

• Ensure reviews cover tolerance stack-up, structural/fatigue analysis, gear/contact analysis, electromagnetic and thermal analysis, bearing/interface loads, motor-drive matching, servo implications, manufacturability, CTQs, supplier capability, reliability risk, testability and cost.

• Ensure Manufacturing, Quality and SCM participate from the architecture stage, not only after drawings are released.

Configuration & Engineering Change Control





• Establish disciplined control of requirements, product configurations, drawings, BOMs, firmware versions, analysis models, test specifications, deviations, ECNs and as-built prototype states.

• Reject prototype evidence that cannot be traced to a known design and software configuration.

Customer & Programme Technical Interface

• Own technical translation of customer requirements and approve the technical acceptance basis for evaluation and qualification.

• Support the CEO and customer-facing programme owner without taking commercial ownership, pricing authority or sales responsibility.

Candidate Profile

Education

B.E. / B.Tech with M.E. / M.Tech preferred, or equivalent advanced engineering experience, in Mechanical, Mechatronics, Electrical/Electronics, Electromechanical Systems, Controls/Robotics or a closely related engineering discipline. Significant: Academic qualification does not compensate for lack of real product-development and design-authority evidence.

Experience

15+ years with progressively senior technical responsibility in precision electromechanical or motion-control products. The strongest candidate should have personally taken integrated hardware through requirements → architecture → detailed design → prototype → failure → redesign → DV → industrialisation / customer qualification.

Must-Have Technical Depth

• Integrated actuator / servo-system architecture through DV.

• Hands-on depth in at least two of: precision transmissions / gear systems; electric motors / magnetics; servo drives / power electronics; embedded motion control.

• Strong systems understanding of bearings/interfaces, tolerance engineering, thermal management, sensing/encoders, servo performance, test/validation, DFM, technical supplier assessment, reliability and configuration management. Preferred Industry Background

• Precision motion systems / robotics actuators / industrial servo systems.

• Harmonic, planetary or cycloidal transmission systems.

• Electric drives, aerospace electromechanical actuation or high-performance automotive/EV electromechanical products.

• Precision industrial components where physical product release, supplier development and customer qualification are central.

📌 Chief Engineer (Pune)
🏢 Antal International
📍 Pune

Reply to this offer

Impress this employer describing Your skills and abilities, fill out the form below and leave Your personal touch in the presentation letter.

Subscribe to this job alert:

Get the latest job offers by email for: chief engineer (pune) / pune