19 Nov
|
Experis
|
Chandigarh
19 Nov
Experis
Chandigarh
Role & responsibilities
Router (De-panelling)
Preferred candidate profile
: Router / PCB De-panelling Operator
Particular
Details
Designation
Router (De-panelling)
Position / Grade
Operator
Head Count
Function
SMT Production / PCB De-panelling
Reports To
Production Engineer / Supervisor
Recommended Experience
13 years in PCB/PCBA manufacturing or router/de-panelling operation
Education
ITI / Diploma or equivalent technical qualification
1. Router / De-panelling Machine Operation
- Operate PCB/PCBA router and de-panelling equipment according to approved SOPs and work instructions.
- Load and unload PCB panels carefully using defined handling methods.
- Select and run the approved routing program for the corresponding PCB/PCBA model.
- Verify PCB part number, revision, routing fixture and machine program before start.
- Perform machine start-up and shutdown according to defined procedures.
- Monitor machine operation continuously during the routing cycle.
- Never make unauthorized changes to routing programs, coordinates, cutting paths or process parameters.
2. PCB / PCBA De-panelling
- Separate individual PCBAs from manufacturing panels according to the approved routing profile.
- Ensure routing is completed without damaging the PCB, solder joints, components or connectors.
- Handle populated PCB panels carefully during loading and unloading.
- Ensure clean separation around PCB edges and defined break-away areas.
- Avoid excessive mechanical stress, bending or twisting during handling.
- Ensure routed PCBAs are placed in approved ESD-safe trays/containers after separation.
3. Pre-Operation Setup Verification Before starting production, verify:
- Correct PCB/PCBA model
- Correct part number and revision
- Correct routing program
- Correct fixture/jig
- Correct router bit/tool
- Fixture clamping condition
- Dust extraction/vacuum availability
- Machine safety interlocks
- Required production documentation
Immediately stop and escalate any mismatch before routing begins. 4. Routing Program & Fixture Verification
- Verify the approved machine program against the production model before operation.
- Ensure the correct routing fixture/jig is fitted and properly secured.
- Check PCB orientation before starting the cycle.
- Ensure no PCB/components interfere with fixture location or clamping points.
- Confirm the program and physical setup after every model changeover.
- Support first-piece verification before continuing serial production.
5. Router Bit / Cutting Tool Control
- Check router-bit condition before starting production.
- Monitor cutting-tool condition during operation.
- Identify signs of worn or damaged router bits, including poor edge finish, excess burrs or abnormal cutting noise.
- Replace router bits according to defined tool-life or replacement instructions.
- Maintain tool-change records where required.
- Use only approved router-bit type/diameter for the specified product.
- Escalate abnormal or repetitive tool wear.
6. First-Off Verification
- Support first-piece/first-off inspection after machine setup or model changeover.
- Check routed PCB/PCBA dimensions and physical condition according to defined inspection requirements.
- Verify routing path and PCB-edge quality.
- Check for visible component or PCB damage.
- Ensure first-off approval is obtained where required before serial production continues.
- Escalate any deviation immediately.
7. Post De-panelling Inspection Visually inspect routed PCBAs for:
- PCB cracks
- Edge damage
- Burrs
- Chipping
- Delamination
- Scratches
- Track/pad damage near PCB edges
- Component damage
- Connector damage
- Component displacement
- Solder-joint damage
- Abnormal cutting marks
Segregate any suspect board rather than allowing it to proceed to the next operation. 8. PCB Edge Quality Control
- Ensure routed edges meet defined drawing/workmanship requirements.
- Monitor cut quality continuously throughout production.
- Verify that excessive burrs or fiber breakout are not generated.
- Report changes in edge quality that may indicate router-bit wear or machine/fixture issues.
- Avoid unauthorized manual trimming or modification of PCB edges.
- Escalate recurring edge defects to Production/Process Engineering.
9. NG / Damaged Board Segregation
- Immediately segregate PCBAs showing routing-related abnormalities.
- Maintain clearly defined OK, NG, Hold and Rework locations.
- Prevent damaged or suspect PCBAs from being mixed with approved parts.
- Inform Production/Quality of any repeated damage.
- Maintain required defect identification and traceability.
- Route suspect material for Quality disposition.
10. Dust Extraction & Cleanliness Control
- Ensure the router dust extraction/vacuum system is operational before production.
- Monitor dust accumulation during operation.
- Keep cutting and fixture areas free of PCB dust and debris.
- Clean equipment at the defined frequency using approved methods.
- Do not use uncontrolled cleaning methods that could contaminate or damage PCBAs.
- Report ineffective suction or excessive dust generation immediately.
11. PCB / PCBA Handling
- Handle PCBAs carefully to prevent mechanical and electrostatic damage.
- Never stack unprotected PCBAs in a manner that allows components to contact each other.
- Avoid touching components, solder joints or exposed contacts unnecessarily.
- Use designated ESD-safe racks, trays or containers.
- Prevent board bending while loading/unloading fixtures.
- Follow defined maximum stacking/handling requirements.
12. ESD Compliance
- Strictly follow plant ESD-control requirements.
- Use ESD wrist straps, footwear, garments and grounded workstations as required.
- Use only approved ESD-protected trays and containers.
- Verify ESD controls before handling electronic assemblies.
- Immediately report damaged/missing ESD protection.
- Prevent PCBAs from contacting uncontrolled surfaces.
13. Product Changeover
- Support product/model changeover according to the production schedule.
- Remove the previous product and fixture systematically.
- Perform required line clearance.
- Load the correct fixture and approved routing program.
- Verify router-bit/tool requirements.
- Perform first-piece routing and obtain defined verification.
- Support reduction of changeover time without bypassing setup checks.
14. Production Output & Productivity
- Operate the router according to the planned production cycle.
- Achieve shift-wise production/output targets while maintaining quality.
- Record produced quantities and downtime where required.
- Minimize avoidable operator-related machine stoppages.
- Report material shortages, fixture issues or machine abnormalities quickly.
- Support continuous improvement of routing cycle time and productivity.
15. Basic Machine Monitoring & Troubleshooting
- Monitor equipment for:
- Abnormal noise or vibration
- Router spindle alarms
- Vacuum/dust extraction problems
- Fixture/clamping issues
- Tool-breakage alarms
- Sensor errors
- Conveyor or handling abnormalities
- Perform only authorized operator-level corrective actions.
- Escalate technical faults to Maintenance/Technical personnel.
- Do not bypass alarms or safety systems to continue production.
16. Autonomous / Daily Maintenance
- Perform authorized daily operator-level equipment checks.
- Clean machine surfaces, fixtures and designated areas.
- Check visible fixture and tooling condition.
- Check dust-extraction function.
- Complete daily machine check sheets.
- Inform Maintenance of abnormal wear or machine condition.
- Support TPM/autonomous-maintenance activities.
17. Traceability & Documentation
- Maintain required product and process traceability.
- Record production lot/batch/serial details where applicable.
- Maintain
- Production quantity
- Rejection quantity
- Router-bit/tool changes
- Machine downtime
- First-off verification
- Changeover records
- Daily machine checks
- Follow barcode/MES scanning procedures where implemented.
18. Safety Compliance
- Operate router equipment only after required training and authorization.
- Ensure machine guards and safety interlocks remain operational.
- Never bypass safety switches/interlocks.
- Keep hands away from moving cutters/spindles.
- Stop the machine before any authorized cleaning or tool replacement activity.
- Use specified PPE.
- Immediately report unsafe equipment conditions.
19. 5S & Workplace Organization
- Maintain strong 5S around the routing/de-panelling area.
- Keep fixtures, router bits, tools, PCB trays and cleaning equipment in designated locations.
- Maintain clear segregation of OK, NG, Hold and unprocessed PCBs.
- Regularly remove routing waste and PCB dust through the approved disposal process.
- Keep aisles and operating areas clean and unobstructed.
- Participate in 5S audits and improvement actions.
20. Shift Handover
Provide clear handover covering
- Running PCB/PCBA model
- Production quantity completed/pending
- Router-bit/tool status
- Machine condition
- Fixture condition
- Quality concerns
- NG boards
- Machine alarms/downtime
- Pending maintenance actions
Ensure records are updated before shift completion. 21. Continuous Improvement & Training
- Participate in Kaizen, TPM, 5S and productivity-improvement activities.
- Highlight recurring routing defects and equipment issues.
- Suggest improvements for PCB loading/unloading, fixture handling and changeover.
- Support reduction of routing-cycle time and tool-related losses.
- Complete required router/de-panelling, ESD, quality and safety training.
- Participate in periodic competency assessments.
Key Skills / Competencies
- PCB/PCBA router and de-panelling machine operation
- PCB fixture/jig handling
- Router-bit/tool handling
- PCB physical-damage identification
- PCB edge-quality inspection
- Basic machine-alarm understanding
- First-off inspection support
- Product/model changeover
- ESD-safe PCBA handling
- Product traceability
- TPM/autonomous maintenance
- 5S and shop-floor discipline
- Strong safety awareness
- Attention to detail
Key Performance Indicators
KPI Area
Measurement
Production
Output vs. production target
Quality
De-panelling rejection rate
Damage
PCB/component damage due to routing
First Pass
First-pass routed PCB acceptance
Tooling
Router-bit life / controlled usage
Downtime
Operator/tool/fixture-related stoppages
Changeover
Model changeover time
Traceability
Production-record compliance
Machine
Daily machine-check compliance
ESD
ESD handling compliance
5S
Workstation 5S compliance
Safety
Zero unsafe machine-operation incidents
📌 Router (De-panelling) (Chandigarh)
🏢 Experis
📍 Chandigarh