Quality Control (QC) Engineer / Inspector – Hot Dip Galvanizing (HDG)

Quality Control (QC) Engineer / Inspector – Hot Dip Galvanizing (HDG)

21 Nov
|
Budhia Steel
|
Jaipur

21 Nov

Budhia Steel

Jaipur

Key Roles & Responsibilities

- Incoming & Pre-Galvanizing Inspection:
- Raw fabricated steel ka surface inspection (oil, grease, rust, welding slag, burrs check karna).
- Venting & drainage holes verify karna hollow/tubular sections mein taaki air pocket na bane aur zinc entrapment/blast hazard avoid ho.
- Material straightness, distortion risk aur fabrication clearance check karna.
- Process / Pre-Treatment Monitoring:
- Chemical tank parameters monitor karna: Degreasing, Acid Pickling (HCl bath concentration & iron content), Water Rinsing, and Fluxing (specific gravity, temperature & pH).
- Drying table aur pre-heating timing track karna taaki zinc splash kam ho.
- Zinc kettle temperature monitoring ($445^circtext{C} - 455^circtext{C}$) aur zinc bath composition (pure zinc / aluminium addition) verify karna.
- Post-Galvanizing Inspection & Quality Testing:
- Coating Thickness Measurement: Elcometer / Digital DFT gauge se micron thickness check karna standard requirement ke hisaab se (e.g., 65 / 86 / 100+ microns).
- Visual Defect Inspection: Dross pimples, ash deposits, bare spots (uncoated areas), lumps, zinc runs, sags, white rust (wet storage stain) aur rough coating check karna.
- Adhesion & Uniformity Tests: Pivoted hammer test / knife test for adhesion aur Preece test (copper sulphate dip test for uniformity) perform karna standard specifications ke mutabik.
- Touch-up & Rectification:



Approved zinc-rich cold galvanizing paint ya zinc solder spray se minor defect rework standard limit mein supervise karna.
- Documentation & Audit Compliance:
- Daily Inspection Reports (DIR), Batch inspection logs, aur Test Certificates (TC / MTC) prepare karna.
- Client inspection / Third-Party Inspection (TPI) jaise RITES, PowerGrid, NTPC, BV, SGS, TUV ke physical verification aur sampling ko handle/witness karwana.
- Non-Conformance Reports (NCR) raise karna aur CAPA (Corrective & Preventive Action) maintain karna.
- Measuring instruments (DFT meter, digital thermometers, hydrometers) ka calibration record maintain rakhna.

Required Skills & Qualifications

- Education: Diploma / B.Tech in Mechanical / Metallurgy / Chemical Engineering (ya B.Sc Chemistry).
- Experience: 2 se 6 saal ka direct shop floor quality control experience Hot Dip Galvanizing plant ya structural steel galvanizing setup mein.
- Technical Knowledge:
- Relevant Galvanizing Standards: IS 2629, IS 4759, IS 6745, ASTM A123 / A153, ISO 1461.
- Hands-on experience with Elcometer (DFT meter), temperature pyrometers, hydrometers, aur chemical titration basics.
- Sound knowledge of welding defect visibility, steel chemistry impact (Sandelin effect / silicon-phosphorus reactivity).
- Skills: Blueprint/Drawing reading, TPI inspection handling, documentation skills, shop floor coordination.

Pay: ₹11,000.00 - ₹45,000.00 per month

Work Location: In person

📌 Quality Control (QC) Engineer / Inspector – Hot Dip Galvanizing (HDG)
🏢 Budhia Steel
📍 Jaipur

Reply to this offer

Impress this employer describing Your skills and abilities, fill out the form below and leave Your personal touch in the presentation letter.

Subscribe to this job alert:

Get the latest job offers by email for: quality control (qc) engineer / inspector – hot dip galvanizing (hdg) / jaipur

Subscribe to this job alert:

Get the latest job offers by email for: quality control (qc) engineer / inspector – hot dip galvanizing (hdg) / jaipur