Embedded HW/SW Engineer - Medical Devices (Bengaluru)

Embedded HW/SW Engineer - Medical Devices (Bengaluru)

22 Nov
|
Neemtree
|
Bengaluru

22 Nov

Neemtree

Bengaluru

Role Overview:This is a full-stack embedded role. You will work directly with the ASR/ML team on the audio pipeline, the software platform team on FHIR and HMIS adapters, QA on IEC 60601-1 and ISO 14971, and manufacturing on DFM, harness, and the calibration line.What You'll Own:You will own the embedded hardware and firmware end to end - from PCB design through field reliability.1. PCB Design and Hardware Bring-up:- Design PCBs from schematic capture through layout: carrier board, isolated patient-side island, biosignal front-end, and power subsystem boards, using KiCad or Altium.- Select components from datasheets, maintain the BOM, and manage DFM reviews with manufacturing.- Bring up SoC carrier boards: USB 3.2, MIPI CSI-2, M.2, HDMI, GPIO; validate with a logic analyser and oscilloscope.- Design and verify the isolated patient-side island: 2xMOPP barrier, isolated DC-DC converters, digital isolators across UART bridges, creepage and clearance per IEC 60601-1.- Implement ECG front-end (ADS1293): right-leg drive, common-mode rejection, and plate-contact detection.- Design the power subsystem: 24 V medical PSU, LiFePO4 BMS, UPS switchover with zero-glitch handover.2. Firmware and Embedded Software :- Write and maintain JetPack Linux service containers: device-manager, ASR-bridge, vision, report-builder, FHIR-sync,



admin-fleet.- Implement UART/TTL drivers for medical grade sensors; output a unified sensor-reading struct; never alter numeric values after they leave the sensor.- Implement Bluetooth LE drivers and manage BT LE radio scheduling to avoid audio dropouts.- Write screen-read OCR fallback pipeline for sensor reading.- Control ROBOTIS Dynamixel XL430 pan-tilt servos via U2D2/TTL bus: face-tracking loop at <= 20 Hz, soft stops, servo scheduling outside speech turns.- Manage the USB device tree.3. OTA, Security, and Fleet Management:- Build and maintain a signed OTA pipeline: Ed25519 firmware signing, A/B partitioning, watchdog rollback, model hot-swap without reboot.- Implement fleet telemetry: per-unit uptime, UART timeout counts, BT pairing failure counts, NVMe SMART health - store-and-forward over LTE.- Keep the platform secure: encrypted patient records at rest, signed OTA, consent on every recording, DPDP Act 2023 compliance.4. ISO/IEC Compliance and Test:- Own the embedded contributions to IEC 60601-1 (electrical safety), IEC 60601-1-2 (EMC), IEC 62304 (software lifecycle), ISO 14971 (risk management), and ISO 13485 (QMS).- Design and validate PCBs to pass medical-grade standards: patient leakage current, dielectric strength across the 2xMOPP barrier, ESD immunity, radiated and conducted emissions.- Build calibration station fixtures and bench rigs; run EVT and DVT acceptance tests; contribute DHR and DMR entries in ERPNext.- Coordinate pre-compliance EMC scans, formal IEC lab testing, and CDSCO/BIS filing support.What You Bring:- 3 - 5 years of hands-on embedded hardware and firmware experience,



with at least some exposure to medical or regulated devices.- PCB schematic capture and layout in KiCad or Altium: you have designed a multi-layer board that went into production, including component selection, DFM review, and BOM management.- Experience testing and validating PCBs against industry or ISO-family standards - patient leakage, isolation barriers, EMC pre-compliance, or equivalent regulated-industry testing.- Embedded Linux on ARM SoCs: systemd, containerisation (Docker), device tree, U-Boot or equivalent secure-boot chain.- UART/TTL and Bluetooth LE peripheral drivers written from vendor protocol documents, not example code.- USB device tree management: V4L2, ALSA, SANE, HID, or similar subsystems under Linux.- Power electronics: DC-DC converters, BMS, UPS switchover logic, rail sequencing.- Logic analyser and oscilloscope fluency: you debug UART framing, SPI timing, and power rail noise with instruments, not guesswork.- Python or C++ to write firmware services, bench test scripts, and calibration tooling.- Comfortable working alongside QA, regulatory affairs, and manufacturing teams - you read a risk file and contribute to it.Positive to Have:- Formal IEC 60601-1 or IEC 60601-1-2 lab testing experience (submissions, non-conformance closure).- ISO 13485 QMS contribution: DHR/DMR entries, supplier qualification, calibration SOPs.- BT LE GATT profile implementation from scratch.- OTA pipeline design: A/B partitioning, signed firmware, watchdog rollback.- LTE modem bring-up under Linux.- Experience with medical sensor OEM. (ref:hirist.tech)

📌 Embedded HW/SW Engineer - Medical Devices (Bengaluru)
🏢 Neemtree
📍 Bengaluru

Reply to this offer

Impress this employer describing Your skills and abilities, fill out the form below and leave Your personal touch in the presentation letter.

Subscribe to this job alert:

Get the latest job offers by email for: embedded hw/sw engineer - medical devices (bengaluru) / bengaluru

Subscribe to this job alert:

Get the latest job offers by email for: embedded hw/sw engineer - medical devices (bengaluru) / bengaluru