Project Associate (Bengaluru)

Project Associate (Bengaluru)

22 Nov
|
QOSMIC
|
Bengaluru

22 Nov

QOSMIC

Bengaluru

Type: Full Time, Fixed Term (6 –12 months) | 0–2 years Work Experience

Location:
Bengaluru (on-site) Compensation (CTC): Determined by the candidate’s qualifications and relevant experience Joining Date: Immediate

About the Role
We're building the optical highway to the cosmos Join us as a Project Associate in Electrical on one of our core hardware programmes. You will design, simulate, build, debug and test the electronics inside our optical communication terminals – precision drive and sensing circuits, power supplies, and the microcontroller firmware that brings them to life. This is a fixed-term role of 6–12 months, with extension or conversion to a permanent position based on performance and programme needs. It suits a recent B.
Tech or M.
Tech graduate who wants real hardware, real debugging, and real ownership from the first week. Responsibilities ● Design and simulate analog circuits in LTspice: op-amp signal chains, sensor front ends, instrumentation amplifiers, active filters, and actuator driver stages ● Design and verify power electronics: buck, boost and flyback converters, LDOs, auxiliary and bias supplies, rail sequencing, current limiting, and protection ● Capture schematics and lay out PCBs in Altium and KiCad: component selection, stack-up, grounding and return paths, partitioning of analog, digital and power sections, clearance, decoupling, and manufacturing outputs ● Bring up and debug boards: staged power-up, rail verification, soldering and rework, and systematic fault isolation with oscilloscopes, logic analysers, DMMs, and current-limited supplies ● Write and debug embedded C firmware on STM32 for bring-up and test: GPIO, timers, ADC and DAC, SPI, I²C, UART, and DMA ● Characterise circuits and subsystems: frequency and step response, noise floor, linearity, drift with temperature, and driver performance limits, with data logged and analysed in Python or MATLAB ● Support closed-loop system testing with the team: calibration, system identification,



and tuning experiments ● Run pre-compliance EMI/EMC and environmental checks — conducted and radiated emissions, susceptibility, ESD, and thermal — and fix what they find ● Build test jigs, harnesses, interface boards (RS-422/485, SPI, CAN), and hardware-in-the-loop setups ● Document designs, test procedures and results, present at design reviews, and keep all design files under version control Requirements ● B.
Tech/M.
Tech in Electrical, Electronics, ECE, or Instrumentation Engineering; 0–2 years of experience, where strong project or internship work counts ● Analog fundamentals: op-amps (gain-bandwidth, slew rate, offset, noise, stability), filters, and amplifier design for sensors and actuators ● Data converters: solid understanding of ADCs and DACs – resolution, sampling, aliasing, references, settling, and how converter choice affects a measurement or control loop ● Power electronics fundamentals: linear versus switching regulators, common converter topologies, magnetics and capacitor selection, ripple, efficiency, thermal dissipation, and protection ● Circuit simulation in LTspice: transient, AC, noise, and stability analysis, and the judgement to know when a model can be trusted ● PCB design in Altium and KiCad: multiple boards taken through schematic, layout, fabrication, and bring-up ● Board-level debugging: SMD soldering and rework, oscilloscopes and logic analysers, and a methodical approach to isolating faults ● Embedded C on STM32 or similar ARM Cortex-M parts, from HAL to register level, with on-target debugging over SWD ● Interfaces: SPI, I²C, UART,



and working knowledge of RS-422/485 and CAN ● Tools you should already use or pick up quickly: – Simulation: Ltspice and Ngspice – PCB design: Altium Designer or KiCad – Firmware: Embedded C, C and C++ (STM32CubeIDE or a GCC/Make toolchain, with an ST-Link or J-Link debugger) – Bench: oscilloscope, logic analyser, DMM, programmable power supply, electronic load, function generator, soldering station, and hot-air rework – Analysis and version control: Python or MATLAB, and Git (version control) ● Not afraid to go deep into datasheets, reference manuals and application notes, and to work from them to a design that holds up on the bench ● EMI/EMC awareness: noise sources and coupling paths, filtering, shielding, and layout practice; IPC standards for PCB design and assembly; component derating ● Python or MATLAB for data analysis and plotting ● Clear documentation, honest reporting of results, and the drive to learn fast Nice-to-Have ● Precision motion control or positioning systems, and driving reactive loads such as motors or actuators ● Low-noise sensing and signal conditioning for precision measurement ● Control systems basics: PID, Bode plots, loop stability, and filtering ● Exposure to optical or photonic systems ● Space or defence hardware exposure: vibration and thermal testing, or NASA, ECSS, and MIL-STD standards ● Student satellite, rocketry, or robotics team experience, or personal hardware projects you can show

What We Offer
● Hands-on ownership of flight-bound hardware, from bench prototype to qualification ● World-class lab facilities and test equipment, with mentorship from the core electronics team ● A clear path to extension or full time conversion based on performance ● Collaborative multi-disciplinary research environment

How to Apply
Send your resume and a brief note about your interests to: [email protected]. Include links to boards, schematics, or code you have built.

📌 Project Associate (Bengaluru)
🏢 QOSMIC
📍 Bengaluru

Reply to this offer

Impress this employer describing Your skills and abilities, fill out the form below and leave Your personal touch in the presentation letter.

Subscribe to this job alert:

Get the latest job offers by email for: project associate (bengaluru) / bengaluru

Subscribe to this job alert:

Get the latest job offers by email for: project associate (bengaluru) / bengaluru